I have a Ford KA 1.3 1998 manual, i need to change the starter motor?

I have a Ford KA 1.3 1998 manual, i need to change the starter motor,

is it an easy job, can u instruct me please :)
I have a Ford KA 1.3 1998 manual, i need to change the starter motor?
the stater motor has 2 terminals and is connected with 2 very heavy duty cables which are easily removed and to remove and replace the starter motor is easy

Honda Civic D15B3 starter motor problem?

Hey i m in a big problem. Currently i have honda civic 95 and i have changed many starter motors for this engine and they work only for 1 or 2 days and after that they will get slow wont allow me to even crank my engine further.



Can anyone please tell me that is it possible to find some starter motor for my engine D15B3 with greater rpm that fits exactly on my engine. May be up coming models like D16W9. If possible please do tell me as quickly as possible. Please tell me any other if possible ?



Thank n Regards.



Salman.
Honda Civic D15B3 starter motor problem?
Your starter motor is not bad. Buy a new battery if yours is over 4 years old and make sure the battery cables are good and making a good connection. Finally, your engine may be overheating and harder to turn over or your timing could be off to make the engine hard to turn over. Remove the spark plugs and the starter should turn over the engine easily. If not, you have an engine mechanical problem.

If i have to change the starter on a 1987 plymouth horizon will i have to jack the motor up to do it?

the exhaust may have to be removed. or maybe in the way
If i have to change the starter on a 1987 plymouth horizon will i have to jack the motor up to do it?
no you will not Most starters are easy to get to.

Good Luck
If i have to change the starter on a 1987 plymouth horizon will i have to jack the motor up to do it?
No, you should not have to Jack the motor up. However it would help you out of have the car off the ground a bit for better access to the starter.
Nope. Disconnect the negative battery lead. Now slide under the car, back of the engine where the transmission bolts up to it. See that thing with the big wire? That's the starter, take off the big wire, then the little wire. Take out the bolts, slide it out. Go to the auto parts store and have them test it to make sure, putting it back in is the reverse of removing it.

How do i change the starter in my 1994 gm car whith a 2.3litter engine?

please i need an answer fast or a web site where i can find it
How do i change the starter in my 1994 gm car whith a 2.3litter engine?
Well, be willing to work for this one. Go to autozone.com they have a how to section... this job isn't too easy.

Good luck, heck I'm not busy bring it to Arkansas and I'll do it.

Ho do i change a starter on a 1996 chrysler sebring?

PLS. ADD SOME MORE INFO IN YOUR INQUIRY,LIKE WHAT SIZE ENGINE?IS IT AUTOMATIC?I'LL GET BACK TO YOU WHEN YOU EDIT YOUR QUESTION.

hair styling

make full lips look

Starter on a 1987 Nissan pickup Truck?

How do I change my starter on a 1987 2WD 4 cyl. Nissan Pickup Truck and where can i find a diagram?
Starter on a 1987 Nissan pickup Truck?
your best bet is to get a repair manual
Starter on a 1987 Nissan pickup Truck?
The starter is there under the intake manifold and held on with two 14 mm headed long bolts from the front top and bottom bolt fron the back side transmission side. A couple 3%26quot; extensions and 14mm socket and bloody knuckles. You will have the feeling of a mechanic. Just disconnect the battery first 10mm battery clamp. The battery terminal at the starter is a 12mm nut and don't forget to reconnect the battery ground under the starter bolt from the back side. A good mechanic can perform the job in less than a hour. I have done Lot's of them and know how to maneuver the starter in and out so It takes me about 15 minutes. Of course I have almost $100.000 in snap-on tools and 35 years experience.

How hard is it to change a starter on a 95 mercury grand marques, and where is it located.?

The starter is located on the lower passenger side of the engine on this particular vehicle. To remove/replace the starter is fairly straightforward as it is with most vehicles. On this particular one, there are three 10mm bolts that secure it to the transmission. The most difficult part of the job will be access to the top bolt. Hope this helps.
How hard is it to change a starter on a 95 mercury grand marques, and where is it located.?
Removal



WARNING: When servicing starter or performing any maintenance in the area of starter, note the heavy gauge input lead connected to the starter solenoid is hot at all times. Make sure the protective cap is installed over the terminal and is replaced after service.



NOTE : When battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the Powertrain Control Module (PCM) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.

Less than an hour labor time.





Disconnect battery ground cable.

Raise and support the vehicle on a hoist.

Disconnect starter cable and push-on connector from starter solenoid. CAUTION : When disconnecting hard-shell connector at S-terminal, grasp the plastic shell and pull off. Do not pull on wire. Be careful to pull straight off to prevent damage to the connector and the S-terminal. If any part of the connection is damaged, replace the damaged components.

Remove upper mounting bolt.

Remove lower mounting bolt and starter.

Installation





Position starter motor to engine and install upper and lower bolts finger-tight.

Tighten the upper bolt to 20-27 Nm (15-20 lb-ft).

Tighten the lower bolt to 20-27 Nm (15-20 lb-ft).

Connect starter solenoid connector. Be careful to push straight on and make sure connector locks in position with a notable click or detent.

Install starter cable to starter terminal. Tighten to 9-14 Nm (80-124 lb-in).

Replace red starter solenoid safety cap.

Lower vehicle to floor.

Connect battery ground cable